HelenOS sources

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
hw_read_wait
hw_reset_power_on
hw_set_reset
hw_addr_init
hw_gpio_set_output
hw_gpio_set_value
hw_init_proc
hw_init_led
hw_activate_phy
hw_set_operating_mode
hw_reset_operating_mode
hw_noise_floor_calibration
hw_set_freq
hw_freq_switch
hw_set_rx_filter
hw_set_bssid
hw_rx_init
hw_init_pll
hw_set_init_values
hw_calibration
hw_reset
hw_init
/*
 * Copyright (c) 2015 Jan Kolarik
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * - Redistributions of source code must retain the above copyright
 *   notice, this list of conditions and the following disclaimer.
 * - Redistributions in binary form must reproduce the above copyright
 *   notice, this list of conditions and the following disclaimer in the
 *   documentation and/or other materials provided with the distribution.
 * - The name of the author may not be used to endorse or promote products
 *   derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

/** @file hw.c
 *
 * AR9271 hardware related functions implementation.
 *
 */

#include <macros.h>
#include <usb/debug.h>
#include <errno.h>
#include <nic.h>
#include <ieee80211.h>
#include "hw.h"
#include "wmi.h"

/** Try to wait for register value repeatedly until timeout is reached.
 *
 * @param ar9271 Device structure.
 * @param offset Registry offset (address) to be read.
 * @param mask   Mask to apply on read result.
 * @param value  Required value we are waiting for.
 *
 * @return EOK if succeed, ETIMEOUT on timeout,
 *         error code otherwise.
 *
 */
static errno_t hw_read_wait(ar9271_t *ar9271, uint32_t offset, uint32_t mask,
    uint32_t value)
{
        for (size_t i = 0; i < HW_WAIT_LOOPS; i++) {
                udelay(HW_WAIT_TIME_US);

                uint32_t result;
                wmi_reg_read(ar9271->htc_device, offset, &result);
                if ((result & mask) == value)
                        return EOK;
        }

        return ETIMEOUT;
}

static errno_t hw_reset_power_on(ar9271_t *ar9271)
{
        wmi_reg_t buffer[] = {
                {
                        .offset = AR9271_RTC_FORCE_WAKE,
                        .value = AR9271_RTC_FORCE_WAKE_ENABLE |
                            AR9271_RTC_FORCE_WAKE_ON_INT
                },
                {
                        .offset = AR9271_RC,
                        .value = AR9271_RC_AHB
                },
                {
                        .offset = AR9271_RTC_RESET,
                        .value = 0
                }
        };

        wmi_reg_buffer_write(ar9271->htc_device, buffer,
            sizeof(buffer) / sizeof(wmi_reg_t));

        udelay(2);

        wmi_reg_write(ar9271->htc_device, AR9271_RC, 0);
        wmi_reg_write(ar9271->htc_device, AR9271_RTC_RESET, 1);

        errno_t rc = hw_read_wait(ar9271,
            AR9271_RTC_STATUS,
            AR9271_RTC_STATUS_MASK,
            AR9271_RTC_STATUS_ON);
        if (rc != EOK) {
                usb_log_error("Failed to wait for RTC wake up register.\n");
                return rc;
        }

        return EOK;
}

static errno_t hw_set_reset(ar9271_t *ar9271, bool cold)
{
        uint32_t reset_value = AR9271_RTC_RC_MAC_WARM;

        if (cold)
                reset_value |= AR9271_RTC_RC_MAC_COLD;

        wmi_reg_t buffer[] = {
                {
                        .offset = AR9271_RTC_FORCE_WAKE,
                        .value = AR9271_RTC_FORCE_WAKE_ENABLE |
                            AR9271_RTC_FORCE_WAKE_ON_INT
                },
                {
                        .offset = AR9271_RC,
                        .value = AR9271_RC_AHB
                },
                {
                        .offset = AR9271_RTC_RC,
                        .value = reset_value
                }
        };

        wmi_reg_buffer_write(ar9271->htc_device, buffer,
            sizeof(buffer) / sizeof(wmi_reg_t));

        udelay(100);

        wmi_reg_write(ar9271->htc_device, AR9271_RTC_RC, 0);

        errno_t rc = hw_read_wait(ar9271, AR9271_RTC_RC, AR9271_RTC_RC_MASK, 0);
        if (rc != EOK) {
                usb_log_error("Failed to wait for RTC RC register.\n");
                return rc;
        }

        wmi_reg_write(ar9271->htc_device, AR9271_RC, 0);
        wmi_reg_clear_bit(ar9271->htc_device, AR9271_STATION_ID1,
            AR9271_STATION_ID1_POWER_SAVING);

        return EOK;
}

static errno_t hw_addr_init(ar9271_t *ar9271)
{
        uint32_t value;
        nic_address_t ar9271_address;

        for (unsigned int i = 0; i < 3; i++) {
                wmi_reg_read(ar9271->htc_device,
                    AR9271_EEPROM_MAC_ADDR_START + i * 4, &value);

                uint16_t two_bytes = uint16_t_be2host(value);
                ar9271_address.address[2 * i] = two_bytes >> 8;
                ar9271_address.address[2 * i + 1] = two_bytes & 0xff;
        }

        nic_t *nic = nic_get_from_ddf_dev(ar9271->ddf_dev);

        errno_t rc = nic_report_address(nic, &ar9271_address);
        if (rc != EOK) {
                usb_log_error("Failed to report NIC HW address.\n");
                return rc;
        }

        return EOK;
}

static errno_t hw_gpio_set_output(ar9271_t *ar9271, uint32_t gpio, uint32_t type)
{
        uint32_t address;

        if (gpio > 11)
                address = AR9271_GPIO_OUT_MUX3;
        else if (gpio > 5)
                address = AR9271_GPIO_OUT_MUX2;
        else
                address = AR9271_GPIO_OUT_MUX1;

        uint32_t gpio_shift = (gpio % 6) * 5;

        uint32_t temp;
        wmi_reg_read(ar9271->htc_device, address, &temp);

        temp = ((temp & 0x1f0) << 1) | (temp & ~0x1f0);
        temp &= ~(0x1f << gpio_shift);
        temp |= (type << gpio_shift);

        wmi_reg_write(ar9271->htc_device, address, temp);

        gpio_shift = 2 * gpio;

        wmi_reg_set_clear_bit(ar9271->htc_device, AR9271_GPIO_OE_OUT,
            AR9271_GPIO_OE_OUT_ALWAYS << gpio_shift,
            AR9271_GPIO_OE_OUT_ALWAYS << gpio_shift);

        return EOK;
}

static errno_t hw_gpio_set_value(ar9271_t *ar9271, uint32_t gpio, uint32_t value)
{
        wmi_reg_set_clear_bit(ar9271->htc_device, AR9271_GPIO_IN_OUT,
            (~value & 1) << gpio, 1 << gpio);
        return EOK;
}

/**Hardware init procedure of AR9271 device.
 *
 * @param ar9271 Device structure.
 *
 * @return EOK if succeed, error code otherwise.
 *
 */
static errno_t hw_init_proc(ar9271_t *ar9271)
{
        errno_t rc = hw_reset_power_on(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to HW reset power on.\n");
                return rc;
        }

        rc = hw_set_reset(ar9271, false);
        if (rc != EOK) {
                usb_log_error("Failed to HW warm reset.\n");
                return rc;
        }

        rc = hw_addr_init(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to init HW addr.\n");
                return rc;
        }

        return EOK;
}

static errno_t hw_init_led(ar9271_t *ar9271)
{
        errno_t rc = hw_gpio_set_output(ar9271, AR9271_LED_PIN,
            AR9271_GPIO_OUT_MUX_AS_OUT);
        if (rc != EOK) {
                usb_log_error("Failed to set led GPIO to output.\n");
                return rc;
        }

        rc = hw_gpio_set_value(ar9271, AR9271_LED_PIN, 0);
        if (rc != EOK) {
                usb_log_error("Failed to init bring up GPIO led.\n");
                return rc;
        }

        return EOK;
}

static errno_t hw_activate_phy(ar9271_t *ar9271)
{
        wmi_reg_write(ar9271->htc_device, AR9271_PHY_ACTIVE, 1);
        udelay(1000);

        return EOK;
}

static errno_t hw_set_operating_mode(ar9271_t *ar9271,
    ieee80211_operating_mode_t op_mode)
{
        uint32_t set_bit = 0x10000000;

        switch (op_mode) {
        case IEEE80211_OPMODE_ADHOC:
                set_bit |= AR9271_OPMODE_ADHOC_MASK;
                wmi_reg_set_bit(ar9271->htc_device, AR9271_CONFIG,
                    AR9271_CONFIG_ADHOC);
                break;
        case IEEE80211_OPMODE_MESH:
        case IEEE80211_OPMODE_AP:
                set_bit |= AR9271_OPMODE_STATION_AP_MASK;
                /* Fallthrough */
        case IEEE80211_OPMODE_STATION:
                wmi_reg_clear_bit(ar9271->htc_device, AR9271_CONFIG,
                    AR9271_CONFIG_ADHOC);
        }

        wmi_reg_set_clear_bit(ar9271->htc_device, AR9271_STATION_ID1,
            set_bit, AR9271_OPMODE_STATION_AP_MASK | AR9271_OPMODE_ADHOC_MASK);

        ieee80211_report_current_op_mode(ar9271->ieee80211_dev, op_mode);

        return EOK;
}

static errno_t hw_reset_operating_mode(ar9271_t *ar9271)
{
        errno_t rc = hw_set_operating_mode(ar9271, IEEE80211_OPMODE_STATION);
        if (rc != EOK) {
                usb_log_error("Failed to set opmode to station.\n");
                return rc;
        }

        return EOK;
}

static errno_t hw_noise_floor_calibration(ar9271_t *ar9271)
{
        uint32_t value;
        wmi_reg_read(ar9271->htc_device, AR9271_PHY_CAL, &value);

        value &= 0xfffffe00;
        value |= (((uint32_t) AR9271_CALIB_NOMINAL_VALUE_2GHZ << 1) & 0x1ff);

        wmi_reg_write(ar9271->htc_device, AR9271_PHY_CAL, value);

        wmi_reg_clear_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_NF_CALIB_EN);

        wmi_reg_clear_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_NF_NOT_UPDATE);

        wmi_reg_set_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_NF_CALIB);

        errno_t rc = hw_read_wait(ar9271, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_NF_CALIB, 0);
        if (rc != EOK) {
                usb_log_error("Failed to wait for NF calibration.\n");
                return rc;
        }

        wmi_reg_set_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_NF_CALIB_EN);

        wmi_reg_clear_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_NF_NOT_UPDATE);

        wmi_reg_set_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_NF_CALIB);

        return EOK;
}

static errno_t hw_set_freq(ar9271_t *ar9271, uint16_t freq)
{
        /* Not supported channel frequency. */
        if ((freq < IEEE80211_FIRST_FREQ) || (freq > IEEE80211_MAX_FREQ))
                return EINVAL;

        /* Not supported channel frequency. */
        if ((freq - IEEE80211_FIRST_FREQ) % IEEE80211_CHANNEL_GAP != 0)
                return EINVAL;

        uint32_t tx_control;
        wmi_reg_read(ar9271->htc_device, AR9271_PHY_CCK_TX_CTRL, &tx_control);
        wmi_reg_write(ar9271->htc_device, AR9271_PHY_CCK_TX_CTRL,
            tx_control & ~AR9271_PHY_CCK_TX_CTRL_JAPAN);

        /* Some magic here. */
        uint32_t synth_ctl;
        wmi_reg_read(ar9271->htc_device, AR9271_PHY_SYNTH_CONTROL, &synth_ctl);
        synth_ctl &= 0xc0000000;
        uint32_t channel_select = (freq * 0x10000) / 15;
        synth_ctl = synth_ctl | (1 << 29) | (1 << 28) | channel_select;

        wmi_reg_write(ar9271->htc_device, AR9271_PHY_SYNTH_CONTROL, synth_ctl);

        ieee80211_report_current_freq(ar9271->ieee80211_dev, freq);

        return EOK;
}

errno_t hw_freq_switch(ar9271_t *ar9271, uint16_t freq)
{
        wmi_reg_write(ar9271->htc_device, AR9271_PHY_RFBUS_KILL, 0x1);

        errno_t rc = hw_read_wait(ar9271, AR9271_PHY_RFBUS_GRANT, 0x1, 0x1);
        if (rc != EOK) {
                usb_log_error("Failed to kill RF bus.\n");
                return rc;
        }

        rc = hw_set_freq(ar9271, freq);
        if (rc != EOK) {
                usb_log_error("Failed to HW set frequency.\n");
                return rc;
        }

        rc = hw_activate_phy(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to activate physical layer.\n");
                return rc;
        }

        udelay(1000);
        wmi_reg_write(ar9271->htc_device, AR9271_PHY_RFBUS_KILL, 0x0);

        rc = hw_noise_floor_calibration(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to do NF calibration.\n");
                return rc;
        }

        return EOK;
}

errno_t hw_set_rx_filter(ar9271_t *ar9271, bool assoc)
{
        uint32_t additional_bits = 0;

        if (assoc)
                additional_bits |= AR9271_RX_FILTER_MYBEACON;
        else
                additional_bits |= AR9271_RX_FILTER_BEACON;

        uint32_t filter_bits = AR9271_RX_FILTER_UNI |
            AR9271_RX_FILTER_MULTI | AR9271_RX_FILTER_BROAD |
            additional_bits;

        wmi_reg_write(ar9271->htc_device, AR9271_RX_FILTER, filter_bits);

        return EOK;
}

errno_t hw_set_bssid(ar9271_t *ar9271)
{
        ieee80211_dev_t *ieee80211_dev = ar9271->ieee80211_dev;

        nic_address_t bssid;
        ieee80211_query_bssid(ieee80211_dev, &bssid);

        uint32_t *first_4bytes = (uint32_t *) &bssid.address;
        uint16_t *last_2bytes = (uint16_t *) &bssid.address[4];

        wmi_reg_write(ar9271->htc_device, AR9271_BSSID0,
            uint32_t_le2host(*first_4bytes));

        wmi_reg_write(ar9271->htc_device, AR9271_BSSID1,
            uint16_t_le2host(*last_2bytes) |
            ((ieee80211_get_aid(ieee80211_dev) & 0x3fff) << 16));

        return EOK;
}

errno_t hw_rx_init(ar9271_t *ar9271)
{
        wmi_reg_write(ar9271->htc_device, AR9271_COMMAND,
            AR9271_COMMAND_RX_ENABLE);

        errno_t rc = hw_set_rx_filter(ar9271, false);
        if (rc != EOK) {
                usb_log_error("Failed to set RX filtering.\n");
                return rc;
        }

        wmi_reg_write(ar9271->htc_device, AR9271_MULTICAST_FILTER1, ~0);
        wmi_reg_write(ar9271->htc_device, AR9271_MULTICAST_FILTER2, ~0);

        /* Disable RX blocking. */
        wmi_reg_clear_bit(ar9271->htc_device, AR9271_DIAG, (0x20 | 0x02000000));

        return EOK;
}

static errno_t hw_init_pll(ar9271_t *ar9271)
{
        /* Some magic here (set for 2GHz channels). But VERY important :-) */
        uint32_t pll = (0x5 << 10) | 0x2c;

        wmi_reg_write(ar9271->htc_device, AR9271_RTC_PLL_CONTROL, pll);

        wmi_reg_write(ar9271->htc_device, AR9271_RTC_SLEEP_CLOCK,
            AR9271_RTC_SLEEP_CLOCK_FORCE_DERIVED);
        wmi_reg_set_bit(ar9271->htc_device, AR9271_RTC_FORCE_WAKE,
            AR9271_RTC_FORCE_WAKE_ENABLE);

        return EOK;
}

static void hw_set_init_values(ar9271_t *ar9271)
{
        uint32_t reg_offset;
        uint32_t reg_value;

        size_t size = ARRAY_SIZE(ar9271_2g_mode_array);

        for (size_t i = 0; i < size; i++) {
                reg_offset = ar9271_2g_mode_array[i][0];
                reg_value = ar9271_2g_mode_array[i][1];
                wmi_reg_write(ar9271->htc_device, reg_offset, reg_value);
        }

        size = ARRAY_SIZE(ar9271_2g_tx_array);

        for (size_t i = 0; i < size; i++) {
                reg_offset = ar9271_2g_tx_array[i][0];
                reg_value = ar9271_2g_tx_array[i][1];
                wmi_reg_write(ar9271->htc_device, reg_offset, reg_value);
        }

        size = ARRAY_SIZE(ar9271_init_array);

        for (size_t i = 0; i < size; i++) {
                reg_offset = ar9271_init_array[i][0];
                reg_value = ar9271_init_array[i][1];
                wmi_reg_write(ar9271->htc_device, reg_offset, reg_value);
        }
}

static errno_t hw_calibration(ar9271_t *ar9271)
{
        wmi_reg_set_bit(ar9271->htc_device, AR9271_CARRIER_LEAK_CONTROL,
            AR9271_CARRIER_LEAK_CALIB);
        wmi_reg_clear_bit(ar9271->htc_device, AR9271_ADC_CONTROL,
            AR9271_ADC_CONTROL_OFF_PWDADC);
        wmi_reg_set_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_TX_CALIB);
        wmi_reg_set_bit(ar9271->htc_device, AR9271_PHY_TPCRG1,
            AR9271_PHY_TPCRG1_PD_CALIB);
        wmi_reg_set_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_CALIB);

        errno_t rc = hw_read_wait(ar9271, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_CALIB, 0);
        if (rc != EOK) {
                usb_log_error("Failed to wait on calibrate completion.\n");
                return rc;
        }

        wmi_reg_set_bit(ar9271->htc_device, AR9271_ADC_CONTROL,
            AR9271_ADC_CONTROL_OFF_PWDADC);
        wmi_reg_clear_bit(ar9271->htc_device, AR9271_CARRIER_LEAK_CONTROL,
            AR9271_CARRIER_LEAK_CALIB);
        wmi_reg_clear_bit(ar9271->htc_device, AR9271_AGC_CONTROL,
            AR9271_AGC_CONTROL_TX_CALIB);

        return EOK;
}

errno_t hw_reset(ar9271_t *ar9271)
{
        /* Set physical layer as deactivated. */
        wmi_reg_write(ar9271->htc_device, AR9271_PHY_ACTIVE, 0);

        if (ar9271->starting_up) {
                wmi_reg_write(ar9271->htc_device,
                    AR9271_RESET_POWER_DOWN_CONTROL,
                    AR9271_RADIO_RF_RESET);

                udelay(50);
        }

        /* Cold reset when RX is enabled. */
        uint32_t config_reg;
        wmi_reg_read(ar9271->htc_device, AR9271_COMMAND, &config_reg);
        if (config_reg & AR9271_COMMAND_RX_ENABLE)
                hw_set_reset(ar9271, true);

        errno_t rc = hw_init_pll(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to init PLL.\n");
                return rc;
        }

        udelay(500);

        wmi_reg_write(ar9271->htc_device, AR9271_CLOCK_CONTROL,
            AR9271_MAX_CPU_CLOCK);

        udelay(100);

        if (ar9271->starting_up) {
                wmi_reg_write(ar9271->htc_device,
                    AR9271_RESET_POWER_DOWN_CONTROL,
                    AR9271_GATE_MAC_CONTROL);

                udelay(50);
        }

        hw_set_init_values(ar9271);

        /* Set physical layer mode. */
        wmi_reg_write(ar9271->htc_device, AR9271_PHY_MODE,
            AR9271_PHY_MODE_DYNAMIC);

        /* Reset device operating mode. */
        rc = hw_reset_operating_mode(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to reset operating mode.\n");
                return rc;
        }

        /* Set initial channel frequency. */
        rc = hw_set_freq(ar9271, IEEE80211_FIRST_FREQ);
        if (rc != EOK) {
                usb_log_error("Failed to set channel.\n");
                return rc;
        }

        /* Initialize transmission queues. */
        for (unsigned int i = 0; i < AR9271_QUEUES_COUNT; i++) {
                wmi_reg_write(ar9271->htc_device,
                    AR9271_QUEUE_BASE_MASK + (i << 2), 1 << i);
        }

        /* Activate physical layer. */
        rc = hw_activate_phy(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to activate physical layer.\n");
                return rc;
        }

        /* Calibration. */
        rc = hw_calibration(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to calibrate device.\n");
                return rc;
        }

        rc = hw_noise_floor_calibration(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to calibrate noise floor.\n");
                return rc;
        }

        /* Byteswap TX and RX data buffer words. */
        wmi_reg_write(ar9271->htc_device, AR9271_CONFIG, 0xA);

        return EOK;
}

/** Initialize hardware of AR9271 device.
 *
 * @param ar9271 Device structure.
 *
 * @return EOK if succeed, error code otherwise.
 */
errno_t hw_init(ar9271_t *ar9271)
{
        errno_t rc = hw_init_proc(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to HW reset device.\n");
                return rc;
        }

        rc = hw_init_led(ar9271);
        if (rc != EOK) {
                usb_log_error("Failed to HW init led.\n");
                return rc;
        }

        usb_log_info("HW initialization finished successfully.\n");

        return EOK;
}
/* [<][>][^][v][top][bottom][index][help] */
HelenOS homepage, sources at GitHub
HelenOS sources

root/uspace/drv/nic/ar9271/hw.c

DEFINITIONS
